{"id":11,"date":"2021-11-11T23:41:44","date_gmt":"2021-11-11T23:41:44","guid":{"rendered":"https:\/\/ivanovaautomation.com\/?page_id=11"},"modified":"2025-04-17T21:30:48","modified_gmt":"2025-04-17T21:30:48","slug":"gallery","status":"publish","type":"page","link":"https:\/\/ivanovaautomation.com\/?page_id=11","title":{"rendered":"Gallery"},"content":{"rendered":"\r\n

A sample of some projects.<\/h1>\r\n\r\n\r\n\r\n

\u00a0<\/h2>\r\n\r\n\r\n\r\n\r\n\r\n
\"ControlLogix<\/figure>\r\n\r\n\r\n\r\n

A ControlLogix PLC upgrade for a processing machine that was being run on a SLC5\/05. The main rack was replaced and 2 remote SLC racks were converted to Ethernet control by this PLC.<\/h2>\r\n

\"Fork<\/p>\r\n

A fork photo detector with a rubber flag added to the side of a transport cart to ensure the cart was in position as the optical linear encoder was prone to getting dirty and skipping counts. This made sure the cart returned to the home position and if not in position the cart was moved slowly until in position and the encoder was then recalibrated.<\/h2>\r\n\r\n\r\n
\r\n
\r\n

\"Sample<\/p>\r\n<\/figure>\r\n<\/div>\r\n\r\n\r\n

From a simple controls update to a complete retrofit, and design of new equipment, precise CAD drawn schematics are provided for every job along with copies of PLC and HMI programs.\u00a0<\/h2>\r\n

\u00a0<\/p>\r\n

\"\"<\/div>\r\n

\u00a0<\/p>\r\n

\u00a0<\/p>\r\n

\u00a0<\/p>\r\n

\u00a0<\/p>\r\n

\u00a0<\/p>\r\n

\u00a0<\/p>\r\n

\u00a0<\/p>\r\n

\u00a0<\/p>\r\n

\u00a0<\/p>\r\n

\u00a0<\/p>\r\n\r\n\r\n\r\n\r\n\r\n

\"Sudio5000<\/figure>\r\n\r\n\r\n\r\n

PLC programming from simple updates to complete automation projects. This is a sample of Rockwell\u2019s Studio 5000 software for the Allen Bradley ControlLogix and CompactLogix families<\/h2>\r\n\r\n\r\n\r\n
\u00a0<\/div>\r\n\r\n\r\n\r\n
\"Rockwell<\/figure>\r\n\r\n\r\n\r\n

Believing in continual education I attend many training events and seminars. This is one of a few certificates received at a traveling Rockwell event.<\/h2>\r\n\r\n\r\n\r\n
\u00a0<\/div>\r\n
\u00a0<\/div>\r\n\r\n\r\n
\r\n
\"Ivanova<\/a><\/figure>\r\n<\/div>\r\n\r\n\r\n
\u00a0<\/div>\r\n

\u00a0<\/p>\r\n

\u00a0<\/p>\r\n

\"Allen-Bradley<\/p>\r\n

DeviceNet rack for remote inputs & outputs. The rack is one of several read and controlled by an Allen-Bradley ControlLogix PLC through Ethernet<\/h2>\r\n
\r\n

\u00a0<\/h2>\r\n

Safety in machine controls is a priority during design and build. Physical E-stop safety circuits to prevent any operation are needed. If the machine the SLC5\/03 PLC pictured below only had the E-stop wired to a PLC input and relied on the PLC program then processing it, this PLC \u2013 which is faulted and not running its program \u2013 would not change the state of any of the outputs shown on. Any motor, drive, pump, blower or anything else run by this PLC would never stop if this PLC stopped running its program, possibly injuring and killing workers at or near the equipment.<\/h2>\r\n\r\n\r\n\r\n\r\n\r\n

Normally when a PLC faults the firmware shuts off all outputs, but on this specific unit any output that was on stays on. Outputs on also stay on if this PLC is put in Program Mode, which is how this safety anomaly was discovered.<\/h2>\r\n\r\n\r\n\r\n\r\n
\r\n
\"SLC<\/figure>\r\n<\/div>\r\n\r\n\r\n
\r\n

A physical E-stop safety relay is needed to interrupt the power to the PLC outputs to stop all operation. The PLC shown has been marked on all sides bright red and is kept only for training purposes as it is too dangerous to be used in any application.<\/h2>\r\n<\/div>\r\n

\u00a0<\/p>\r\n

\r\n

\u00a0<\/p>\r\n<\/div>\r\n

\u00a0<\/p>\r\n

\"Micrologix1400<\/p>\r\n

A Micrologic 1400 Ethernet system with additional I\/O. This PLC uses an analog output to control the speed of a VFD driven motor.<\/h2>\r\n

\u00a0<\/p>\r\n

\"Hydraulic<\/p>\r\n

A hydraulic press needed an expensive pressure gauge replaced that read the force the ram was applying that was 0 to 300,000 pounds. I suggested a more economical replacement using a pressure transducer providing a signal to a digital readout. This also has the capability of being easily calibrated that a regular pressure gauge does not allow.<\/h2>\r\n

\u00a0<\/p>\r\n

\"\"<\/p>\r\n\r\n\r\n\r\n

\r\n
<\/figure>\r\n
<\/figure>\r\n
<\/figure>\r\n
<\/div>\r\n<\/div>\r\n","protected":false},"excerpt":{"rendered":"

A sample of some projects. \u00a0 A ControlLogix PLC upgrade for a processing machine that was being run on a […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"page-templates\/template_fullwidth.php","meta":{"om_disable_all_campaigns":false,"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"footnotes":""},"class_list":["post-11","page","type-page","status-publish","hentry"],"aioseo_notices":[],"jetpack-related-posts":[],"jetpack_sharing_enabled":true,"_links":{"self":[{"href":"https:\/\/ivanovaautomation.com\/index.php?rest_route=\/wp\/v2\/pages\/11","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/ivanovaautomation.com\/index.php?rest_route=\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/ivanovaautomation.com\/index.php?rest_route=\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/ivanovaautomation.com\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/ivanovaautomation.com\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=11"}],"version-history":[{"count":50,"href":"https:\/\/ivanovaautomation.com\/index.php?rest_route=\/wp\/v2\/pages\/11\/revisions"}],"predecessor-version":[{"id":409,"href":"https:\/\/ivanovaautomation.com\/index.php?rest_route=\/wp\/v2\/pages\/11\/revisions\/409"}],"wp:attachment":[{"href":"https:\/\/ivanovaautomation.com\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=11"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}